火凤皇5-9MM专业大调直切断机 铁线直线机 下料机

主要技术参数：

the main technical parameters:

产品的性能与特点：

product performance and features:

1，本机适用于铁线、不绣钢线、镀锌线、铝线、水（粉）抽线等金属线材的调直切断。

1. this machine is suitable for wire, stainless steel wire, galvanized wire, aluminum, water (powder) draw lines and other metal wire straightening and cutting.

2，如需调直方线，扁线等异形线，请联系本公司订制。

2. to straighten party lines, flat lines, contour lines, please contact the company ordered.

3, 送线轮、切刀等采用优质合金钢，并通过真空热处理，耐磨性强，使用寿命延长。调直块可采用铸铁、合金、塑料王等，所有轴类部件全部采用40cr或45#钢，并经调直处理，齿轮则全部采用锻坯，经高直及齿面高频淬火，硬度高达hrc55-58度。

3. sending wire wheel, such as the use of high- steel cutter and vacuum heat treatment, wear resistance, longer life. straightening block can be cast iron, alloys, plastics wang, all shaft parts are all 40cr or 45 # steel, and after straightening process, the gear is used in all forging billet, straight and tooth surface by high frequency hardening, hardness up hrc55-58 degrees.

4, 调直轴与高直压轮将线材在切断前调直，送线压紧手柄调节送线压紧轮，使线材能均匀送进，调直轴是产品形成的关键所在，通过调直轴上的调直块和调直固定来调整产品的水平垂直，使之符合要求。调节压紧手柄，使线材更加水平垂直和使线材生产速度增减。Zui后调节枪杆上的白钢刀，使产品长度符合要求。

4, straight shaft with high pressure wheel straight before cutting the wire straightening, wire feeding pressing the pinch roller lever to adjust wire feed, the wire can even feed, direct modulation axis is the key product formed by direct modulation straightening blocks and tone straight shaft fixed to adjust the horizontal and vertical products to conform to re adjusting the pressing handle, the wire and the wire is more horizontal and vertical production rate increase or decrease. finally, adjust white blades gun on the length of the product to meet the re

5,速度快，工作性能稳定，操作简单。

5. fast, stable performance, simple operation.

6, 本产品为本公司完全自方研发，经国内外上千家用户，十多年的使用检验，已是一款完全成熟的产品。

6. the product-oriented company is fully self-party research and development, by thousands of users at home and abroad, more than a decade of use test, is a fully mature product.

5-9带枪大直线机实拍全图

5-9 large linear machine gun real shot full map

5-9大直线机不带枪实拍全图

5-9 large linear machine gun not really making the whole map

本机所配线架实拍图

this machine really making plans mdf

皮带轮调节手柄，可随时调紧传动皮带，有效防止皮带在长时带工作之后变松。

pulley adjustment handle, ready to tighten the belt, effectively preventing the belt after a long time with work loose. 

送线轮压力调节手柄，共有前后两组，用此手柄来调节送线速度。

sending wire wheel pressure regulating handle, a total of around two, use this handle to adjust wire feed speed. 

 送线轮左右调节手柄，前后共两组，用此手柄来调节线材左右位置，以使线材居于调线轴孔及定位切断枪孔的中心位置。

about sending wire wheel adjustment handle, before and after the two groups, with the handle to adjust the lateral position of the wire to the wire spool living adjustment and the positioning hole cutting gun hole in the center position.

 快速倒顺开关，让操作可靠方便。

fast inverted switch, allowing the operator reliable and convenient.

导线孔加油盒，里面填上棉布，再加润滑油，可以让调直过程更平顺，减少断线。

wire hole filling box, which fill cotton, plus lubricating oil, allowing straightening process more smooth, reduce breakage.

六组调直块，可轻松调直线种材质的线材，使用方便，操作简单。

six groups of straight blocks kinds of materials can be easily transferred straight wire, easy to use, easy to operate.

机器保养及操作注意事项

machine maintenance and operation precautions

第一，本机所采用的电源为3相380伏，千万别要缺相，如缺相，则铁定烧坏电机。

first, the machine used for the 3-phase 380-volt power supply, do not want to phase, such as phase, then definitely burn out the motor.

第二，本机的转运部位请定期加油润滑。

second, the transfer of parts of the machine periodically lubricated.

第三，安装时请可靠接地。

third, when installing reliable grounding.

第四，工作时严禁打开机盖，否则万一断线时极易发生工伤事故，此操作要领请切记切记！！！

fourth, the work machine cover must not be opened, otherwise accidents can easily occur in the event of disconnection, this operating essentials please remember! ! !

第五，枪头部位请对墙，以免跑线时刺伤车间其他工作人员。

fifth, the tip portion of the wall please, in order to avoid stab workshop run line when other staff.

第六，当一卷线材将调完时，请在剩下三圈时停掉机器，否则剩余线头部位有可能产生甩尾现象，很容易伤到操作工人。如果认为线材弄浪严重，有经验的工人可以用钳子夹着线头推送，但我们并不鼓励这种操作方式。

sixth, when a roll of wire will transfer finished, please stopped three times during the rest of the machine, otherwise the remaining thread parts may produce drift phenomenon, it is easy to hurt workers in the operation. if you think the wire waves get serious, experienced workers can use pliers sandwiched thread push, but we do not encourage this mode of operation.

本公司服务承诺

the company pledges

凡在本公司采购的所有产品，均可享受一年免费维修服务。保修期满之后，依旧提供全程保养服务，维修配件收取成本费用。

where in the purchase of all products, can enjoy one year of free maintenance service. after the warranty expires, still provide full maintenance service and repair charge cost accessories.

此系列产品分三大类this series of products into three main categories：tz1.0-2.5   tz2.5-5.5    tz5.0-9.0

如需了解其它型号直线机详情，请点击下面对应图片即可

for other models straight line machines, please click on the following image to correspond

小号调直机

small straightening machine

想要了解中号直线机点击请进

for medium linear machine click come

本产品的品牌是火凤皇，型号是TZ5-9，产品别名是调直机，产品用途是家居生活用品，建材行业，种类是铁线调直机，规格是1500*600*1300，适用行业是五金线类制品行业，五金机械是调直切断下料用，用途是五金线材调直下料